{"product_id":"taidacent-non-contact-liquid-level-sensor-capacitive-sensor-flow-sensor-level-transmitter-float-switch-water-level-switch-high-and-low-level-output","title":"Taidacent non contact liquid level sensor capacitive sensor flow sensor level transmitter float switch water level switch high and low level output","description":"\u003ch3\u003eTaidacent non contact liquid level sensor capacitive sensor flow sensor level transmitter float switch water level switch high and low level output\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eParameter Product model: XKC-Y26-V Supply voltage（Vin）：DC\n5-24V Output mode：High and low level electric current： 5mA The output\nvoltage（high level）： Vin; The output voltage（low level）： 0V; The output\ncurrent： ≤100mA Response time： 500mS Working temperature： -20~85℃ Sensor\nsensitivity Pipe outer diameter D(mm) D≥100，Sense container wall or tube wall\nthickness L(mm) 20±2； Pipe outer diameter D(mm) 100\u0026gt;D≥80 ，Sense container wall\nor tube wall thickness L(mm) 15 ± 2； Pipe outer diameter D(mm) 80\u0026gt;D≥60，Sense\ncontainer wall or tube wall thickness L(mm) 12 ±1.5；Pipe outer diameter D(mm)\n60\u0026gt;D≥40，Sense container wall or tube wall thickness L(mm) 7 ±1.0；Pipe outer\ndiameter 40\u0026gt;D≥30，Sense container wall or tube wall thickness L(mm) 5 ±1.0；\nOuter diameter of pipe D(mm) 30\u0026gt;D≥20，Sense container wall or tube wall\nthickness L(mm) 3 ±1.0； pipe outer diameter D(mm) 20\u0026gt;D≥10，Sense container wall\nor tube wall thickness L(mm) 1.5 ±0.5 Applicable pipe diameter range: ≥10mm\nLiquid level accuracy: ±1.5mm humidity: 5%~100% Material: PC V0 Fireproof\nmaterial Waterproof performance: IP65 Install into a flat cistern as shown in\nthe figure above The height of the sensed liquid level is related to the\nsensitivity of the sensor. The higher the sensitivity, the lower the sensed\nliquid level Note: The liquid level is sensed in the upper and lower edges of\nthe sensor, which is normal. The induction sheet can be tightly attached to\nthe pipe with strong glue, or it can be tightened with the pipe with a nylon\ncable tie. Try to avoid metal and other parts where the probe is installed, so\nas not to affect the detection. Pipes made of non-metallic materials with a\nsmooth surface, uniform thickness, tight material, and good insulation\nperformance; such as glass pipes, plastic pipes, PC\/PVC\/PPR pipes, non-\nabsorbent ceramic pipes, acrylic pipes, rubber pipes, etc. or their composites\nPipes made of materials. How to install to the water pipe Install to the non-\nmetal water pipe type as shown Sensitivity adjustment If the non-contact\nliquid level sensor cannot detect or the detected liquid level is too high\nfrom the Y26 sensor. The sensitivity knob can be adjusted with a small\nscrewdriver, and there are two setting methods: 1. Low sensitivity adjustment:\nturn counterclockwise to increase sensitivity. 2. High sensitivity adjustment:\nturn clockwise to lower the sensitivity Product size and physical map Y26\nwiring diagram of various models High and low level output drive small\nelectric relay (coil current ≤100mA) working principle 1.When the black line\nis suspended, it is positive output: When liquid is sensed, the transistor\ncuts off and outputs a high level, and the relay does not pull in when it is\npowered off, When no liquid is sensed, the transistor turns on and outputs a\nlow level, and the relay is energized and closed; 2.When the black wire is\ngrounded (connected to the negative pole of the power supply 0V), it is a\nreverse output: When liquid is sensed, the transistor turns on and outputs a\nlow level, and the relay is energized and closed; When no liquid is sensed,\nthe transistor cuts off and outputs a high level, and the relay does not pull\nin when it is powered off;\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eThe intelligent non-contact liquid level sensor uses advanced signal processing technology and high-speed signal processing chip to break through the influence of the wall thickness of the container and realize the true non-contact detection of the liquid level in the closed container.\u003c\/li\u003e\n         \u003cli\u003eThe liquid level sensor (probe) is installed above and below the outer wall of the container to be tested (the high and low positions of the liquid level). The non-metallic container does not need to be opened, and the installation is simple and does not affect the production.\u003c\/li\u003e\n         \u003cli\u003eThe liquid level of various toxic substances, strong acids, strong alkalis and various liquids in the high-pressure closed container can be detected.\u003c\/li\u003e\n         \u003cli\u003eThe liquid to be tested is required to be electrically conductive, the contact surface is non-metal, and the pipe is easy to install and can be widely used.\u003c\/li\u003e\n         \u003cli\u003eHigh and low level output: If there is induction, the output is high level; no induction, the output is low level. Specially designed for non-metallic pipe liquid level detection\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n\n\n\n","brand":"Taidacent","offers":[{"title":"Default Title","offer_id":41433437372576,"sku":"B07FC8K28F","price":143.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0418\/7134\/3776\/products\/B07FC8K28F.jpg?v=1638521126","url":"https:\/\/dingoship.com.au\/products\/taidacent-non-contact-liquid-level-sensor-capacitive-sensor-flow-sensor-level-transmitter-float-switch-water-level-switch-high-and-low-level-output","provider":"DingoShip AU","version":"1.0","type":"link"}